Lexicon | Mould Making
Mould Making with Epoxy Resin: Guide, Advantages and Professional Tips
Mould making with epoxy resin offers low shrinkage, high strength and low-odour processing. Clean release preparation, suitable epoxy tooling gelcoat and a stable laminate structure are essential for good results.
Summary
When making moulds with epoxy resin, the master pattern is first carefully treated with a release system. Epoxy tooling gelcoat is then applied. Finally, the mould is laminated with woven glass fabric, glass fibre non-crimp fabric or a combination of reinforcement materials.
At a Glance
- Epoxy resin shrinks less than polyester resin
- High strength and good dimensional accuracy
- Low-odour processing compared with polyester resin
- Release agent is crucial for clean demoulding
- Removing air from each laminate layer improves mould quality
Basics
Advantages of Epoxy Resin in Mould Making
Mould making with epoxy resin offers several advantages over mould making with polyester resin. The most important benefits are low shrinkage, high strength and low-odour processing.
Due to its low shrinkage, epoxy resin is suitable for producing dimensionally accurate moulds. This is especially important when later parts must be precise, reproducible and have a clean surface.
| Criterion | Epoxy resin in mould making | Polyester resin in mould making |
|---|---|---|
| Shrinkage | Very low | Higher |
| Strength | Very high | Good |
| Odour | Low odour | Stronger styrene odour |
| Dimensional accuracy | Very good | Depends on application |
Preparation
Required Materials for Mould Making with Epoxy Resin
- Epoxy resin and matching hardener
- Epoxy tooling gelcoat
- Woven glass fabric, glass fibre non-crimp fabric or combined laminate lay-up
- Release agents such as release paste, liquid release wax or PVA release lacquer
- Brushes, foam brushes, mixing cups and scale
- Air release roller for low-bubble laminate layers
- Abrasives, cleaning cloths and protective gloves
Step 1
Apply the Release System Correctly
As the first step, the master pattern or mould must be carefully treated with a release system. Only with a suitable release system can the finished epoxy mould be demoulded cleanly later.
Porous Surfaces
For porous surfaces, release paste should be used. It is applied and then lightly polished out in quick succession. For new moulds, several applications are recommended to create a continuous release layer.
Smooth Moulds
For smooth moulds, liquid release wax can be used. It is applied with a soft cloth. After flashing off, a matt surface forms, which is then lightly polished with a soft cloth. For new moulds, this process should be repeated three to four times.
PVA Release Lacquer for Additional Safety
After treatment with release wax, PVA release lacquer can also be applied. It is applied with a foam brush or soft foam. After a few minutes, a film-like surface forms. This layer must no longer be polished. PVA release lacquer is applied only once. Residues can be removed with warm water after demoulding.
Important
Insufficient release preparation is one of the most common causes of demoulding problems. New, porous or unknown surfaces in particular should be prepared very carefully.
Step 2
Apply Epoxy Tooling Gelcoat
After release preparation, the epoxy tooling gelcoat is applied. Ideally, it is applied twice in a crosswise pattern. The epoxy tooling gelcoat is mixed homogeneously with the matching hardener and applied evenly to the mould with a brush.
After the first layer has gelled, the second layer can be applied. The right time is reached when the first layer has already set but is still tacky. This creates a good bond between the layers.
Professional Tip
Do not apply the gelcoat too thinly. An even gelcoat layer improves surface quality, service life and sandability of the finished mould.
Step 3
Laminate the Mould with Epoxy Resin
Once the tooling gelcoat has cured sufficiently, laminating can begin. Different laminate structures can be used for mould making. A common option is a combination of woven glass fabric, glass fibre non-crimp fabric and another layer of woven glass fabric.
The next layer is ideally laminated wet-on-wet. Each layer must be completely wetted with resin and carefully de-aired. An air release roller is suitable for this.
If the laminate lay-up cannot be carried out wet-on-wet, the last cured layer must be sanded before a new layer is applied. This is necessary to create a secure mechanical bond.
Laminate Lay-Up
Recommended Lay-Up for Epoxy Moulds
One possible lay-up is a sandwich of woven glass fabric, glass fibre non-crimp fabric and woven glass fabric. This structure combines high strength with comparatively low weight.
| Layer | Material | Function |
|---|---|---|
| 1 | Woven glass fabric | Clean bond to gelcoat and surface stability |
| 2 | Glass fibre non-crimp fabric | High strength and stiffness |
| 3 | Woven glass fabric | Cover layer, stabilisation and even finish |
Practice
Avoiding Common Mistakes in Epoxy Mould Making
- Too little release agent: Can lead to strong adhesion and damage during demoulding.
- Uneven gelcoat application: Can cause surface defects or inconsistent layer thickness.
- Poor air removal: Air bubbles weaken the laminate and reduce mould quality.
- Wrong timing when over-laminating: Continuing too late without sanding can reduce adhesion.
- Poor mixing: Epoxy resin and hardener must be accurately dosed and mixed homogeneously.
Find Materials for Epoxy Mould Making
Choose epoxy resin, reinforcement fibres and release agents to match your mould. Fiberglas Discount offers materials for precise mould making, GRP processing and composite projects.
View epoxy resin View release agents View woven glass fabric
Internal Links
Related Topics and Products
FAQ
Frequently Asked Questions About Mould Making with Epoxy Resin
Why use epoxy resin for mould making?
Epoxy resin has very low shrinkage, high strength and low-odour processing. This makes it particularly suitable for dimensionally accurate, high-quality moulds.
Which release agent is suitable for epoxy mould making?
Depending on the surface, release paste, liquid release wax and additionally PVA release lacquer can be used. Porous surfaces require especially careful preparation.
When is the second gelcoat layer applied?
The second layer is applied when the first layer has gelled or set but is still tacky. This creates a good bond between the layers.
Do laminate layers need to be sanded between applications?
If wet-on-wet laminating is used, intermediate sanding is usually not necessary. If the previous layer has already cured, it should be sanded before continuing.
Trust
Why Fiberglas Discount?
Specialist Range
Materials for GRP, mould making, boat building, repair and composite projects.
Practical Selection
Resins, fibres and accessories suitable for beginners and professional users.
Technical Know-How
Clear information for safe processing and long-lasting results.
© 2013 - www.fiberglas-discount.de
© 2018 - Last revision - www.fiberglas-discount.de
© 2025 - Last revision - www.fiberglas-discount.de
© 2026 - SEO, structure and content revision - www.fiberglas-discount.de