How to Properly Use Resinpal 2401 Epoxy Resin – Video Guide
The Resinpal 2401 epoxy resin is a professional 2-component laminating resin with selectable hardener pot lives of 30, 60, or 90 minutes and a heat resistance of up to 120 °C. In this video tutorial, you will learn how to correctly mix resin and hardener, apply it to fiberglass, and achieve a bubble-free cure.
Contents of This Page
Technical Data – Resinpal 2401 Epoxy Resin
| Property | Value |
|---|---|
| Resin Type | 2-Component Epoxy Resin (Laminating Resin) |
| Mixing Ratio (by Weight) | 100 Parts Resin : 25 Parts Hardener |
| Pot Life – 30-Minute Hardener (25 °C) | Approx. 30 Minutes |
| Pot Life – 60-Minute Hardener (25 °C) | Approx. 60 Minutes |
| Pot Life – 90-Minute Hardener (25 °C) | Approx. 90 Minutes |
| Demolding Time at 25 °C | Approx. 24 Hours |
| Full Cure | Approx. 5–7 Days (Room Temperature) |
| Heat Resistance (Tg) | Up to 120 °C |
| Resin Color | Yellowish |
| Odor | Low (Significantly Less Than Polyester Resin) |
| Shrinkage | Minimal |
| Adhesion | Wood, Concrete, Natural Stone, Metal, Fiberglass |
| Available Sizes | 1 kg, 5 kg, 10 kg, 20 kg, 50 kg (Including Hardener) |
| Item Number | 1353 |
Step-by-Step Application Guide
-
1Prepare the Work Area
Ensure a room temperature of 18–25 °C and good ventilation. Cover the work surface with protective film. Prepare mixing cups, a scale, a stirring stick, brushes, and disposable nitrile gloves.
-
2Select the Correct Hardener
Choose according to project size: 30-minute hardener for quick repairs, 60-minute hardener for tack-free coatings and thin laminates, and 90-minute hardener for large molds with multiple layers.
-
3Measure Resin and Hardener
Weigh 100 parts Resinpal 2401 resin and 25 parts hardener separately using a digital scale. Never mix by volume – always mix by weight.
-
4Mix Thoroughly
Add the hardener to the resin and stir evenly for at least 3–4 minutes. Regularly scrape the sides and bottom of the mixing cup.
-
5Transfer the Mixture (Optional)
For quantities over 500 g, transfer the mixture into a second cup and stir briefly again. This reduces the risk of unmixed material along the cup walls.
-
6Lay and Wet Out Reinforcement Fabric
Cut fiberglass matting to size and place it into the mold. Apply the resin-hardener mixture evenly using a laminating brush and fully saturate the fibers.
-
7Remove Air and Eliminate Bubbles
Roll over the saturated laminate using a bubble roller to remove trapped air. Work along the fiber direction with light pressure.
-
8Build Additional Layers
For greater strength, repeat steps 6 and 7 with additional layers. Do not wait for full curing between layers – continue while the laminate remains tacky.
-
9Allow to Cure
Cover the part and allow it to cure for at least 24 hours at room temperature. Post-curing at approximately 60 °C activates the full heat resistance up to 120 °C.
-
10Demold and Finish
Carefully remove the part after 24 hours. Sand edges as needed. Full mechanical strength is achieved after 5–7 days at room temperature.
Professional Tips for Best Results
For mold-making projects with multiple layers, the 90-minute hardener is recommended. For small repairs, the 30-minute hardener is usually sufficient.
At temperatures above 25 °C, pot life decreases significantly. During summer, cool resin and hardener to 18–20 °C before mixing.
For applications exposed to high thermal loads (motorcycle fairings, motorsport components), post-cure at 60–80 °C for 4–6 hours after room-temperature curing.
Resinpal 2401 can be colored using epoxy color pastes. Recommended dosage: maximum 3–5% of total weight.
Safety Information
Always wear disposable nitrile gloves, safety glasses, and an FFP2 respirator when ventilation is insufficient. Epoxy resin may cause allergic reactions. In case of skin contact, wash immediately with soap and water – do not use solvents.
Common Mistakes and How to Avoid Them
- Incorrect Mixing Ratio: The 100:25 ratio must always be measured by weight.
- Insufficient Mixing Time: Stirring for less than 3 minutes may leave unmixed material.
- Working at Low Temperatures: Below 15 °C, the curing reaction slows significantly.
- Using as a Casting Resin: Resinpal 2401 is a laminating resin, not a casting resin.
- No Release Agent Applied: Without a release agent, the resin may permanently bond to the mold.
- Wrong Hardener Selection: Using a 30-minute hardener for large molds can lead to time pressure and application errors.
FAQ – Frequently Asked Questions About Resinpal 2401
What is the mixing ratio for Resinpal 2401?
The mixing ratio is 100 parts resin to 25 parts hardener by weight. Do not measure by volume.
Which hardener should I choose?
30-minute hardener for quick repairs, 60-minute hardener for tack-free coatings, and 90-minute hardener for multi-layer mold construction.
What is the pot life of Resinpal 2401?
Approximately 30 / 60 / 90 minutes depending on the selected hardener at 25 °C. Higher temperatures shorten the pot life.
When can I demold the laminate?
After approximately 24 hours at room temperature. Full strength is reached after 5–7 days.
What is the heat resistance of Resinpal 2401?
Up to 120 °C after complete curing and post-curing.
Is Resinpal 2401 crystal clear?
No. Resinpal 2401 has a natural yellowish color and is designed as a laminating resin, not a casting resin.
Which materials does Resinpal 2401 adhere to?
Excellent adhesion to fiberglass, carbon fiber, aramid fabrics, wood, sanded metal, concrete, and natural stone. Not suitable for PE, PP, or PTFE.
Can I use Resinpal 2401 as an adhesive?
Yes. Thanks to its excellent adhesion, it can also be used as an adhesive and sealant. Fillers such as cotton flock can be added to create a gap-filling compound.
Does Resinpal 2401 have a strong odor?
It produces significantly less odor than polyester resin. For extended work in enclosed spaces, use an FFP2 respirator.
Which package sizes are available?
1 kg + 0.25 kg, 5 kg + 1.25 kg, 10 kg + 2.5 kg, 20 kg + 5 kg, and 50 kg + 12.5 kg.
Can I color Resinpal 2401 with pigment paste?
Yes. Recommended amount: maximum 3–5% pigment paste of the total weight. Only use epoxy-compatible pigments.
What should I do if the laminate remains sticky?
This usually indicates an incorrect mixing ratio, low temperature, or insufficient mixing time. Remove sticky layers mechanically and re-laminate.
Order Resinpal 2401 Today
Professional 2-component epoxy resin with selectable pot life – from €29.99 including hardener, free shipping on orders over €49.
→ View Product in ShopWhat You Need for Application
More Epoxy Resins & Related Products